UBI
Kitchen cabinet storage configurations
Dish storage pull-out basket
A wide shallow pull-out tray with upright plate dividers and separate bowl and cup zones for organized base-cabinet dish storage.
UBI / HARDWARE-OPTIONS
Hardware library
Choose a category, then compare its selections.
Library total: 144 · Shown on this page: 73–96
Cabinet installation and connector configurations
Adjustable cabinet leg
A support fixed beneath a cabinet carcass whose threaded adjustment levels the cabinet before a separate plinth is installed.
Cabinet installation and connector configurations
Concealed wall-cabinet suspension bracket
A hanger fixed inside the upper rear cabinet corner whose hook engages a wall rail while accessible screws permit installation alignment.
Cabinet installation and connector configurations
45° crown and top-line connector
A compact concealed fitting mounted behind two mitred crown or top-line pieces to draw their 45-degree cut edges into a tight visible corner.
Cabinet installation and connector configurations
Adjustable shelf support pin
A compact pin enters a cabinet side-panel system hole and its upper shoulder supports the underside of a removable board shelf.
Cabinet installation and connector configurations
Glass shelf support pin with retainer
A side-panel pin carries the glass edge on a cushioned lower ledge while a compact retainer limits sliding or lifting.
Cabinet installation and connector configurations
Cabinet plinth clip
A concealed clip fixed to the rear of a removable plinth panel snaps around an adjustable cabinet-leg shaft for service access.
Wardrobe storage configurations
Pull-out wardrobe mirror
A slim framed mirror stores along the wardrobe side, pulls out on a guided slide and pivots into a practical viewing angle.
Drawer organization configurations
Modular drawer divider organizer
A shallow insert with intersecting dividers subdivides an existing drawer into orderly compartments for utensils and small items.
Wardrobe storage configurations
Leather-wrapped wardrobe hanging rail
A rigid wardrobe hanging rail uses leather as a decorative surface wrap across its exposed span while metal end supports provide the mounting interface.
Cabinet handle configurations
L-profile concealed edge pull
A continuous L-shaped edge profile fixes along the cabinet-front edge and leaves a slim return lip with a finger-access shadow gap.
Cabinet handle configurations
Front-face recessed cabinet pull
A compact finger pocket is mortised into the broad front face, with a thin rim sitting flush or nearly flush to the panel surface.
Cabinet handle configurations
Leather-clad cabinet-door pull
A projecting cabinet pull uses leather as the tactile finish over a stable grasping core, with compact end anchors fixing it to the cabinet front.
Drawer runner configurations
Synchronized concealed drawer runner system
Paired concealed runners are mechanically linked across a wide drawer so the left and right sides move together and resist racking.
Concealed door pivot configurations
Concealed top-and-bottom pivot hinge
A bottom pivot cassette and matching top pivot are mortised into the door edges, creating one aligned vertical axis with only small floor and ceiling interfaces visible.
Complete drawer box configurations
Complete metal-sided drawer box system
Matched metal side profiles, bottom, back connectors, front-fixing interfaces and compatible runners form one coordinated drawer box rather than separate rails or an organizer insert.
Interior-door handle configurations
Concealed-door lever handle
A compact architectural lever on a small rose provides a clear operating point while preserving the flush wall-and-door composition.
Cabinet hinge configurations
Push-to-open self-opening cabinet hinge
A concealed furniture hinge integrates a reverse self-opening spring so a released handleless door is driven outward by the hinge system.
Wall-cabinet suspension configurations
Visible wall-cabinet suspension bracket
An exposed adjustable cabinet-side hanger hooks onto a compatible wall plate or rail while its housing and adjustment access remain visible inside the cabinet.
Cabinet carcass reinforcement configurations
Cabinet aluminium crossbar brace
A rigid horizontal aluminium extrusion connects the cabinet side panels near the carcass top, reinforcing the cabinet and coordinating the support node below the worktop.
Cabinet lift configurations
Bi-fold lift door support
Paired side mechanisms and articulated arms coordinate two front leaves so a tall cabinet door folds at its centre and rises above the opening.
Display-cabinet lighting configurations
Illuminated glass cabinet shelf
A glass display shelf combines slim side supports with a concealed linear light profile to illuminate the shelf edge and objects below.
Wardrobe rail and lighting configurations
Illuminated wardrobe hanging rail
A load-bearing wardrobe rail integrates a recessed linear light and diffuser along its underside to illuminate garments directly below.
Cabinet hinge configurations
Concealed pin full-overlay soft-close hinge
A slim concealed pin hinge connects a narrow aluminium-frame glass door to the cabinet side, with integrated damping and a full-overlay closed position.
No matching entries. Try another term or choose All.
START WITH YOUR PROJECT
A drawing. A material.
A place you have in mind.
Bring a rendering, CAD drawing, BOQ, sample or reference image. We can start from the information you have.
Start a project